01263 739923 Phone lines are open till 10 pm, 365 days a year - The shop is open from Mon - Fri (7.30 am - 4 pm)

Spud says... "A neat little trick to help with concentricity and bullet alignment is to soft seat the projectile before fully seating it. By this, I mean seat the bullet halfway down to the desired seating depth, spin the case around in the shell holder by 180 degrees, and then completely seat the bullet into the case. This will help with concentricity "run out" of the projectile within the case."

DIES CAN BE FURTHER SORTED BY TYPE & MAKE (USING THE FILTERS BELOW)

There are many types of dies used in reloading...


There are many types of dies used in reloading, I will try and briefly explain the main groups used and any tips for using them.

Full-length dies are used to resize the entire case, neck and body. While this does work the brass a bit more, it also allows the reloaded cartridges to be used in rifles other than the one in which the case was previously fired. One downside to sizing like this; is that the brass does get a little more worked and causes case hardening. But with modern annealing methods, this is no longer a real issue. Some brands make a bushing-style die designed to control the neck tension on the projectile once it’s seated.

Neck-sizing dies as the name implies, will resize only the neck portion of the case, without touching the shoulder or body. For cases that will be reused in the same firearm, neck sizing may be a viable option. These dies can also be called collet dies. Once again, many brands make a bushing style die in this option.

Seating dies are used to seat the projectile into the case mouth; there are a few differing styles of seating die. Some can come with vernier tops to help adjust seating depth in finer detail during load development, and some with just a basic seating plug. All seating dies partially crimped in some form, where the case mouth is tightened around the projectile. Some seating dies can have their seating stem changed for differing styles of the projectile, for instance, a VLD (Very Low Drag) style which will usually be longer than a standard shape.

Small Base dies are for bottleneck-type cases used in tight-chambering semi-automatic, pump or lever-action firearms. The sizer resizes cases below SAAMI minimums, reducing the shoulder and body by a few thousandths. These dies can also come in a full-length bushing style as well.

Crimp dies are usually used in high-recoiling magazine-fed weapons; we can introduce more crimp than a standard seating die to help alleviate the projectile slipping under recoil held in a magazine in this style of firearm. Crimping can also be used for military-style weapons where crimping on the cannelure will help maintain a more consistent pressure with less modern calibres and powders.

Body dies are designed to resize the case body and bump the shoulder position for proper chambering. They do not size the neck and are intended for cases that have become difficult to chamber after repeated firing. After using a body die, the case should be run through the neck die to achieve proper neck tension. They are sold separately or as part of a set.

If taken care of properly, reloading dies will provide years of service to their owner. Most dies are hardened and then micro-polished for that mirror internal finish many of the dies exhibit. Many are also treated with some type of rust preventative before leaving the factory floor. But dies still need some attention before they are put to use.

Clean Your Dies Before First Use

The first step in caring for your dies starts when you receive them. We advocate cleaning all new dies before you begin to use them. Remove the decapping assembly from the die body when your sizing dies. Flush the decapping group with a good degreaser (such as Hornady One-Shot Cleaner & Dry Lube, Birchwood Casey Gun Scrubber, or Shooter’s Choice Quickscrub III) and clean the expander ball.

The only part of the decapping assembly that should contact your brass is the expander ball and the decapping pin. Please pay particular attention to the decapping ball because it depends on the final interior dimension (bullet grip) of your case neck. Ensure you inspect it after cleaning to ensure the surface is clean and free of burrs.

Next, flush the interior of the die body out with some more degreaser. Push a couple of wet patches through the die using a pistol cleaning rod or a dowel rod. Then, run a couple of dry patches through. Reassemble your sizing die, and you should be good to go.

Seating Die Maintenance

Taking apart your seater is pretty simple, depending on the complexity of your seating die. A standard seater requires you to turn the seating stem out of the die body, exposing the seater's interior. Flush and clean both the body and seater as described above. Benchrest sliding sleeve seaters such as Forster or Redding Competition Dies are involved in a few more parts. As you take them apart, could you ensure you know how the spring is oriented and how any other details, such as chamber sleeves or seating plugs, are arranged? Any springs or threads can be wiped down with a rag or patch lightly coated with refined oil. Could you look over the opening in the seating stem for debris? You can twist a patch and use the end to clean out the smaller calibre stems/plugs.

Regular Cleaning and Storage

Regular maintenance of your dies should include routine cleaning. Sizing dies collect excess lube off the cases, and this lube can begin to build up. We have seen dents formed in the case shoulder from the hydraulic compression of the extra lube in the die when the case was sized. We recommend cleaning the dies every 500 to 1000 rounds, depending on how frequently they are used and the cleanliness of your reloading area. For longer-term storage of your die, I recommend putting a light oil or rust preventative on them, especially if you have a shop that has a humid environment.


My reloading area is in the same building (different room) as my woodshop, and I have to watch the dust, so I keep most of my reloading dies covered or stored away. I keep a cover over my press and scales as well.
Shop By
Filters
Calibre
  1. .17 Javelina 1item
  2. .17 Squirrel 1item
  3. .17 Hornady Hornet 1item
  4. .17 Rem Fireball 1item
  5. .17 Tactical 1item
  6. .17 WSM 1item
  7. .17 Remington 1item
  8. .17 Ackley Hornet 1item
  9. .17 Mach IV 1item
  10. .204 Ruger 1item
  11. .20 TNT 1item
  12. .20 PPC 1item
  13. .20 x 47 Lapua 1item
  14. .20 Vartarg 3items
  15. .20 Tactical 1item
  16. .20 Practical 1item
  17. .20 BR Norma 1item
  18. .218 Bee 1item
  19. .219 Donaldson Wasp 1item
  20. .219 Zipper 1item
  21. .220 Beggs 1item
  22. .220 Wilson Arrow 1item
  23. .220 Russian 1item
  24. .220 Swift 1item
  25. .22 BR Rem 1item
  26. .22 Creedmoor 1item
  27. .22 Hornet 1item
  28. .22 Nosler 1item
  29. .22 PPC 2items
  30. .22 Squirrel 1item
  31. .22 Rem Jet 1item
  32. .22/6mm Vartarg 1item
  33. .221 Rem Fireball 1item
  34. .22-250 Remington 1item
  35. .22-250 Improved 40° 1item
  36. .222 Rem Mag 1item
  37. .222 Remington 1item
  38. .223 Remington 2items
  39. .223 Ackley Imp. 40° 1item
  40. .223 WSSM 1item
  41. .224 Valkyrie 1item
  42. .225 Winchester 1item
  43. .243 Winchester 2items
  44. .243 Ack. Imp. 40° 1item
  45. .243 WSSM 1item
  46. 6mm Creedmoor 1item
  47. 6mm PPC 2items
  48. 6mm BR Norma 2items
  49. 6mm Dasher 1item
  50. 6mm XC 2items
  51. 6mm Beggs 1item
  52. 6mm Vartarg 1item
  53. 6 x 47 Lapua 2items
  54. 6mm Int. 1item
  55. 6mm/244 Rem Imp. 1item
  56. 6mm-284 Win 2items
  57. .25 Creedmoor 1item
  58. .25 WSSM 1item
  59. .250 Savage/250-3000 1item
  60. .25-06 Remington 1item
  61. .257 Roberts 1item
  62. .257 Weatherby Mag 1item
  63. .257 Ack. Imp. 1item
  64. .26 Nosler 1item
  65. .260 Remington 1item
  66. .260 Imp. 40° 1item
  67. .264 Win Mag 1item
  68. 6.5mm Grendel 1item
  69. 6.5mm BR Norma 1item
  70. 6.5mm Rem Mag 1item
  71. 6.5mm Creedmoor 1item
  72. 6.5 x 47 Lapua 1item
  73. 6.5 x 55 Swedish Mauser 1item
  74. 6.5-.284 Win (Norma) 1item
  75. 6.8mm Western 1item
  76. 6.8 Rem Special 1item
  77. .270 Winchester 1item
  78. .270 WSM 1item
  79. .280 Ack. Imp. 1item
  80. .28 Nolser 1item
  81. .284 Winchester 1item
  82. 7mm Express 1item
  83. 7mm PRC 1item
  84. 7mm Rem Mag 1item
  85. 7mm Rem Ultra Mag 1item
  86. 7mm-08 Remington 1item
  87. 7mm Rem SA UM 1item
  88. 7mm BR Rem 1item
  89. 7mm STW 1item
  90. 7mm TCU 1item
  91. 7mm WSM 1item
  92. 7 x 57 Mauser 2items
  93. 7mm IHMSA 1item
  94. 7.62 x 39 Russian 1item
  95. .300 AAC Black Out 1item
  96. .30-30 Winchester 1item
  97. .30/40 Krag 1item
  98. .30 x 44 1item
  99. .30 x 47 Lapua 1item
  100. .308 Winchester 2items
  101. .308 Baer 1item
  102. .30 Nosler 1item
  103. .30 x 1.8 1item
  104. .30 IHMSA 1item
  105. .30 BR 1item
  106. .300 Savage 1item
  107. .300 Win Mag 1item
  108. .300 WSM 1item
  109. .300 Norma Mag 1item
  110. .300 Rem SA UM 1item
  111. .300 Rem Ultra Mag 1item
  112. .300 H&H Mag 1item
  113. .30-06 Springfield 1item
  114. .30-06 Ack. Imp. 1item
  115. .30/338 Win Mag 1item
  116. 8mm Rem Mag 1item
  117. .325 WSM 1item
  118. .33 Nosler 1item
  119. .33 XC 1item
  120. .338 Lapua Mag 1item
  121. .338 Win Mag 1item
  122. .338 Edge 1item
  123. .338 Norma Mag 1item
  124. .338 Fed 1item
  125. .348 Winchester 1item
  126. .350 Rem Mag 1item
  127. .35 Whelen 1item
  128. .358 Winchester 1item
Type of product
  1. Full Length Sizers 412items
  2. Neck Sizers 223items
  3. Seating Dies 361items
  4. Full Length Sets 670items
  5. Neck Sizer Sets 170items
  6. Deluxe 3 Die Sets 184items
  7. Rifle Std. 3 & 4 Die & All Pistol Sets 167items
  8. Bushing Full Length Sizers 227items
  9. Bushing Neck Sizers 162items
  10. Micrometer Seating Dies 216items
  11. Bushing Neck Sizer Sets [Type-S & Match] 178items
  12. Bushing Full Length Sets [Type-S & Match] 146items
  13. Redding Type-S Elite Sets 87items
  14. Competition Micrometer Sets 73items
  15. Bushing Neck Dies [Arbor Press Only] 103items
  16. Inline Seating Dies [Arbor Press Only] 140items
  17. Micrometer Seating Dies [Arbor Press Only] 94items
  18. Wilson Ultimate Kits [Std Press Sizer & Arbor Seater] 14items
  19. Bush Bump Die & Sets 47items
  20. Lee Collet Dies 74items
  21. "M" Expanding Neck Dies 23items
  22. Lee Ultimate Dies 10items
  23. Body Dies 90items
  24. Crimp Dies 98items
  25. Full & Body Small Base Dies 29items
  26. Form & Trim Dies 61items
  27. Hydraulic Forming Dies 2items
  28. Dual Ring Carbide Dies 28items
  29. Bullet Feed Dies 1item
  30. Bushings [For Sizing Dies] 674items
  31. Lube Dies 32items
  32. Deprimers 10items
  33. Decapping Pins 25items
  34. Decapping Stems 189items
  35. Expanders 1item
  36. Expander / Sizing Buttons 79items
  37. Seating Stems 172items
  38. Lock Rings 4items
  39. Micrometer Seating Plugs 72items
  40. Die Blanks 36items
  41. Primer Pocket Tools 1item
  42. Powder Through Die 10items
  43. Punches & Bases 55items
  44. Lee Quick Trim 105items
  45. Bullet & Case Feeding 7items
  46. Powder Through Dies 1item
  47. Headspace Measuring 2items
  48. Conversion Kits 2items
  49. Die Lock Rings 10items
  50. Sets 1item
  51. Storage 3items
  52. Tools 5items
  53. Accessories 9items
  54. Spares 26items
  55. Seater Type 2 2items
  56. Seater Type 3 2items
  57. Seater Type 4 2items
  58. Seater Type 5 2items
  59. Seater Type 6 2items
  60. Seater Type 7 2items
  61. Seater Type 8 2items
  62. Seater Type 9 2items
View as

Items 1 to 24 of 140 total

24
  • 12
  • 24
  • 36
  • 72
  • All
per page
Filters
  • Position
  • Name
  • Price
  • Brand
  • Calibre
Position
24
  • 12
  • 24
  • 36
  • 72
  • All
per page
© 2024 1967spud Reloading Supplies Ltd. All rights reserved. | All prices include VAT. 153724219 | Company registered in England and Wales No 09475093 | RFD 36/2491 Norfolk.